Post date: Mar 1, 2017 12:50:43 PM
————— 2017-02-27 —————
郑自明 23:38
今天自己换电阻丝 把暖气修好了
L e҉ o҉ n 23:39
@郑自明 原来什么症状?
郑自明 23:39
没火 电机转一阵就停了
————— 2017-02-28 —————
Julian 06:39
@郑自明 牛/:strong
要是能说稍详细一点或许会帮到别人碰到类似问题的。
郑自明 09:54
学习了暖气系统基本原理 测试出电路控制信号正常 顺藤摸瓜定位到发热电租丝断了 网上订了一个 坑爹的型号太老接口还不一致 果断割开塑胶头顺利装上 测试打
成功[Peace][Peace][Peace]WayneG 10:16
@郑自明 我干过一,二次比你这简单很多的。修好后特有成就感,还省不少$. 你这是什么牌子的机器,烧汽还是油?
郑自明 10:24
烧汽的 牌子好像是Goodman Amana 你是做的什么?
华祥 11:24
@郑自明 大牛了!
郑自明 11:47
@Sean 没有没有 主要有高手指点
华祥 11:50
@郑自明 你没在群里问过,原来高手在民间
Kelvin 12:03
@郑自明 那个零件好像是ignitor?点火的吧?
郑自明 12:05
@Kelvin 是的
郑自明 12:09
通电之后 电路板接受到信号 先发动马达 然后ignitor通电流发热 开气门点火
华祥 12:12
电路板接受到tstat来的W信号 先发动draft inducer, air pressure switch成功闭合后,ignitor通电流发热,开气门点火
郑自明 12:14
@Sean [ThumbsUp] 是w信号?我的理解是两组信号组合
华祥 12:16
W terminal receives 24vac sent from tstat, the G also receives 24vac, but it's not actually needed.
Kelvin 12:17
@Sean 是air vacuum switch 吧?
华祥 12:19
@Kelvin no, pressure switch. Indeed it is sensing the vacuum, but it's not called that.
Kelvin 12:20
@Sean thants
Kelvin 12:20
thanks
Kelvin 12:22
pressure switch is to determine the inducer motor is running in peak?@Sean
华祥 12:23
Correct
华祥 12:24
And there's no blockage in the chimney or chute so the combustion exhaust can go out, otherwise a dangerous situation
郑自明 12:26
@Sean which signal is to control fan only?
华祥 12:27
G
郑自明 12:29
thanks! what is the reason I thought both W and G is required.
Kelvin 12:32
其实家里有备用的flame sensor 和igniter , 基本上可解决90%的问题,
郑自明 12:38
@Kelvin flame sensor的主要作用是什么?
华祥 12:38
@郑自明 no, W turns on heat, and the control board controls blower motor with or without G
华祥 12:41
@Kelvin pressure switch, igniter and capacitors
华祥 12:41
Flame sensor rarely goes bad, only need light sanding
Kelvin 12:42
@Sean use a dollar bill?
华祥 12:42
$100 bill!
Julian 12:43
$100 bill! +1
华祥 12:43
用洗碗的scotch bright
Kelvin 12:43
@郑自明 flame sensor is to detect is flame keep on, if it is bad , fire will go off
华祥 12:46
@eYes! 此段对话是否该收入语录?